How to Use a Bissell Upright Carpet Cleaner
Here's how to use a Bissell upright carpet cleaner: fill the clean tank with formula and water, pretreat tough spots, then pull the machine slowly toward you in overlapping passes and let the carpet dry fully. Empty the dirty tank and rinse the brush roll after every job.
On this page (8 sections)
- What should you do before you start the machine?
- How do you fill and mix the clean water tank?
- Which Bissell formula should you put in the tank?
- How do you pretreat spots and high-traffic areas?
- How do you run the cleaner over the carpet?
- How do you empty and clean the machine afterward?
- How long should the carpet take to dry, and when can you walk on it?
- Which Bissell upright should you use for the job?
Here's how to use a Bissell upright carpet cleaner: fill the clean tank with diluted formula, pretreat spots, then pull the machine slowly toward you in overlapping passes. Empty the dirty tank, rinse the brush roll, and let the carpet dry fully before anyone walks on it.
The steps below work on most Bissell upright models. The ProHeat 2X Revolution Pet Pro Plus is a good reference machine because it has a CleanShot pretreater, dual brush rolls and an Express Clean Mode, and the same order of operations applies to simpler units.
What should you do before you start the machine?
Vacuum the room first and read your model's quick start guide. Loose dirt and pet hair are the main reasons a carpet cleaner leaves gray streaks, because the brush roll just pushes grit around instead of lifting it.
Run a vacuum over the whole area you plan to clean, including under furniture edges. Move small furniture out of the way and put foil or plastic under heavy legs that stay in place.
Check the machine's tanks, cord and brush roll before filling anything.
Test any cleaning formula on a hidden patch of carpet first. Wait for it to dry and check for color change or fiber damage.
This matters most on wool, berber and anything labeled "dry clean only," and our guide on whether you can use a carpet cleaner on area rugs covers those delicate cases in more detail.
How do you fill and mix the clean water tank?
Fill the tank with warm water first, then add the formula at the dilution on the bottle, and never pour in undiluted solution. The two-tank design keeps clean and dirty water separate, and getting the mix right is what stops residue from attracting new dirt.
- Pull the clean tank off the machine and open its cap.
- Add warm water up to the fill line for your cleaning mode.
- Measure formula with the cap and pour it into the water.
- Close the cap firmly and seat the tank until it clicks.
Use warm water, not hot, because very hot water can set some stains and warp the tank. Fill only to the line marked for the job so you don't overfill the dirty tank halfway through.
Which Bissell formula should you put in the tank?
Match the formula to the mess: a deep-clean shampoo for general soil, an oxygen pet formula for urine and odor. Formula choice changes the result more than most people expect, so it's worth picking one on purpose.

A concentrated shampoo for tough ground-in dirt and general deep cleaning.
See it on AmazonBissell calls the Deep Clean Pro 4X Shampoo its most powerful formula, and it carries StainProtect Technology. Bissell says that technology forms a protective barrier on fibers to help resist future stains.
It's a concentrated shampoo, so measure it rather than eyeballing the pour.

An oxygen pet solution for urine, vomit and stubborn odors.
See it on AmazonChoose the Bissell Pet Pro Oxy Upright Solution when pets are the reason you're cleaning. Bissell says it permanently removes stains like urine, blood, vomit and mud from carpets and area rugs.
It uses oxygen to break down stains at the source, and Bissell says it discourages pets from re-soiling the same spot.
Both formulas are made for Bissell and other leading upright deep cleaners when used as directed. Pick one bottle per job rather than mixing them in the same tank.
How do you pretreat spots and high-traffic areas?
Spray or apply pretreater to stains and traffic lanes and give it a few minutes to work before you start the machine. Pretreating does most of the lifting on set-in marks, so the machine only has to rinse them away.
On the ProHeat 2X Revolution Pet Pro Plus, the built-in CleanShot pretreater lets you spray solution directly onto a spot with the machine. On models without that feature, use a spray bottle of diluted formula or the pretreat step built into the machine's settings.
Treat the traffic lanes near doorways and the paths between rooms, not just visible stains. Give the pretreater the dwell time printed on the label, then start cleaning.
Don't let it dry completely on the carpet, because dried formula can leave a dull patch.
How do you run the cleaner over the carpet?
Pull the machine slowly toward you in overlapping lanes and release the spray only on the forward pass. Slow passes give the brush roll time to agitate the fibers and the suction time to pull dirty water back out.
Start at the far end of the room so you don't walk over wet carpet. Push the machine forward while holding the spray trigger, then release the trigger and pull it back over the same lane.
Overlap each new lane by a few inches so you don't leave stripes.
Use the dual brush rolls on the ProHeat to scrub deep dirt with each pass. Express Clean Mode uses less water and Bissell says it leaves carpets dry in about 30 minutes, which suits light refreshes rather than a deep clean.
For heavier soil, MAX Clean Mode with slower passes does more work.
How to use a Bissell upright carpet cleaner on stairs
Use the hose and a stair tool, not the main body, and work one tread at a time from the top down. The upright sits on a stable surface while you guide the tool by hand.
Attach the hose, spray a small section of each tread, and pull the tool back slowly to extract the water. Keep the machine upright so dirty water doesn't spill.
Stairs are where the smaller tools earn their keep, and the same approach works on pet beds and upholstery.
How do you clean upholstery and car seats with the same machine?
Switch to the upholstery tool and test a hidden spot first, then use light passes so you don't over-wet the fabric. The 2-in-1 pet upholstery tool on the ProHeat handles furniture and pet beds, and the 8 ft hose reaches into corners.
For car interiors, the same tool works on fabric seats and floor mats. Our guide on whether you can use a carpet cleaner on car seats covers the fabric types to avoid and the drying steps that prevent mildew.
How do you empty and clean the machine afterward?
Empty the dirty tank, rinse both tanks, and clean the brush roll and cover while everything is still damp. Dirty water left sitting in the tank is what causes the musty smell people blame on the carpet.
- Unplug the machine and remove the dirty tank.
- Pour the dirty water down a toilet or drain, not onto a lawn or driveway.
- Rinse the dirty tank and the clean tank with warm water and let both air dry with the caps off.
- Pull the one-piece brush roll cover and remove hair and thread from the brushes.
- Wipe the machine's base and let everything dry fully before storage.
The removable one-piece brush roll cover on the ProHeat makes this step quick, since you don't have to fight a belt to reach the brushes. Run a tank of clean water through the machine on its rinse setting if the manual calls for it.
How long should the carpet take to dry, and when can you walk on it?
Expect a few hours for a normal pass and about 30 minutes in Express Clean Mode, and keep traffic off until the fibers feel dry. Drying time depends on how wet you left the carpet, the room's humidity, and how many passes you made.
Open windows or run a fan or dehumidifier to move air across the carpet. Turn on ceiling fans and keep pets and kids out of the room until it's dry.
Walk on it in clean socks only if you must cross it.
Avoid walking on damp carpet in shoes, since that grinds dirt back into wet fibers. Don't put furniture back until the carpet is dry, because damp legs can stain or rust the backing.
Which Bissell upright should you use for the job?
The ProHeat 2X Revolution Pet Pro Plus is the pick for most homes because it handles deep cleaning and pet messes with the same machine. It combines dual brush rolls with the CleanShot pretreater and an 8 ft hose for stairs and upholstery.

Dual brush rolls, a built-in pretreater and an 8 ft hose for carpets, stairs and furniture.
See it on AmazonIt has a 3.79 liter tank and a corded power source, and it ships with trial-size Pet Pro Oxy Urine Eliminator and Pro Max Clean + Protect formula to start with. Express Clean Mode is the setting for a quick refresh when you don't need a full deep clean.
If you're deciding between the uprights in the range, our guide on how to use a Bissell Big Green carpet cleaner covers the larger machine's steps. For a wider comparison of the brand's models, see our roundup of the best carpet steam cleaners.
Once the technique is familiar, how to use a Bissell upright carpet cleaner comes down to a simple habit: vacuum first, pretreat the spots, pull slowly in overlapping lanes, and clean the tanks before the dirt dries. That routine keeps the machine working and the carpet looking newer for longer.
Frequently asked questions
How long does a carpet take to dry after using a Bissell upright?
Most carpets feel dry within a few hours, and a low-moisture mode can cut that to about 30 minutes on some models. Open windows or run a fan to speed it up, and keep foot traffic off until the fibers feel dry to the touch.
How much formula do I mix in the clean water tank?
Follow the dilution printed on the formula bottle, and never pour concentrated formula straight into the tank without water. A measuring cap or the tank's fill lines help you get the ratio right, and using more than the label says won't clean better.
Do I need to vacuum before using a Bissell carpet cleaner?
Yes. Vacuuming first lifts loose dirt, crumbs and pet hair so the machine's water and suction can reach the fibers.
Skipping this step leaves grit in the carpet and can clog the brush roll and dirty tank faster.
Can I use a Bissell upright on stairs?
Yes, but you'll need the hose and a stair tool rather than the main body. The upright stays on a stable surface while you work the tool down each tread, and you move the machine by hand as you go.
How often should I clean my carpets with a Bissell?
Clean high-traffic rooms every few months and spot-clean spills right away. Homes with pets or kids usually need more frequent passes, while light-use bedrooms can go longer between deep cleans.
What should I do if the brush roll stops spinning?
Unplug the machine and check the brush roll for hair, thread or debris wrapped around it. Clear the cover and belt area as the manual shows, then test it again; a full dirty tank or a loose tank cap can also cut suction.
About this guide: Our look at using a Bissell upright carpet cleaner draws on maker specs, materials and what owners report. See how we research.



